|
|
| |
Mechanical Engineering Department |
|
|
| |
|
| |
| Research and Publications |
|
| Prof. (Dr.) Ravindra B. Ingle |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
Feb 2006 |
An Experimental Investigation on Dynamic Analysis of High Speed Carbon – Epoxy Shaft in Aerostatic Conical Journal Bearings
International Journal Of Composite Science and Technology Elsevier Publications Inc. UK |
| 2 |
May 2009 |
Identification of the defects in high speed ball bearing using vibrational analysis. International Journal of Mechanical system
( IJMAE) |
| 3 |
April 2010 |
A theoretical investigation on natural frequencies of vibration and noise due to engine and propeller system of Ultra Large Crude Carrier (ULCC)International Journal of Low Frequency Noise, Vibration and Active Control, Multi-Science publ. Co. Essex. UK |
| 4 |
August 2010 |
An Investigation on natural frequencies of hull due to periodic vibrations from engine and propeller system of container ships International Journal of Low Frequency Noise, Vibration and Active Control, Multi-Science publ. Co. Essex. UK |
| 5 |
Nov. 5-11, 2005 |
Finite Element Modeling Strategy for spot welds in Thin – walled sections and Its Validation, 2005 ASME Congress International Mechanical Engineering Congress & Exposition, Orando, Florida USA. |
| 6 |
July 2004 |
Analysis of Carbon – Epoxy Shafts in Aerostatic Conical Journal Bearings
National Journal of Mechanical Engineering The Institution of Engineers (India), |
| 7 |
August 2005 |
An Experimental Investigation and Natural Frequency Analysis of High Speed Carbon – Epoxy Shaft in Aerostatic Conical Journal Bearings
National Journal of Scientific & Industrial Research, NISCAIR, New Delhi |
| 8 |
JULY 18, 2009 |
Design and Analysis of small Container Vessel for Indian Ports
National Journal of institution of Engineers ( India ) Marine Engineering Division Part |
| 9 |
Sep-2009 |
An Investigation on Optimization of Containership Building Design and its Effect on Hull Natural Frequency
National Journal of Marine Engineers Review ( India), |
| 10 |
Jan.18,2010 |
An Investigation on Design Optimization of Small Vessel to Enhance the Coastal Shipping in India National Journal of institution of Engineers ( India ) Marine Engineering Division Part |
| 11 |
24-26 Aug. 2009 |
A Modelfor Study of the Defects in Rolling Element Bearings at Higher Speed by Vibration Signature Analysis.
World Academy of Science, Engineering and Technology Presents
International Conference on Mechanical System and Engineering,
Singapore, |
| 12 |
June 9-12,2002 |
Design Optimization, Dynamic Analysis and Performance Characteristics of Various Composite Shaft in Aerostatic Conical Journal Bearings
International Conference on Tribology, NORDTRIB-02,
Royal Institute of Technology, Stockholm, Sweden, |
|
| |
| Prof V.V. Varade |
| Sr. No. |
Date |
Title of the Paper and Journal. |
| 1 |
23-25 Feb. 2005 |
“Heat Transfer Model for Strand in the Mould Region of Continuous Casting Process”, International Conference on Recent Advances in Material Technology, at National Engg. College, Kovilpatti, Tamilnadu |
| 2 |
March 2004 |
“FEM Model of Heat Transfer for Strand in the Mould region of Continuous Casting Process”, Technical Journal of Institution of Engineers (India) Pune Local Centre, Vol.34 |
|
| |
| Prof.A.K. Bewoor |
| Sr. No. |
Date |
Title of the Paper and Journal. |
| 1 |
Jan. 2006 Issue |
“Experimental investigation of optimization of process parameters for machining non-conducting material by ECDM process” , Manufacturing Technology Today Journal. |
| 2 |
Jan. 2005 Issue |
“Design optimization for reliability importance of components in hydraulic trainer system” Manufacturing Technology Today Journal. |
| 3 |
24th -26th
Oct. 2007 |
‘The Critical Review of Effect of Quality Management System Implementation on Performance of Small and Medium Scale Engineering Industries’, International Conference on Advances in Manufacturing Engg.-2007, Manipal Institute of Tech., Manipal, Karnataka, India. |
| 4 |
18th -20th
Jan. 2007 |
‘A review of use of Artificial Neural Network used for Predicting Tribological Properties’, International Conference on Advances in manufacturing and technology management, P.C.O.E., Thane, Mumbai, India. |
| 5 |
4th - 6th
October 2007 |
‘Advance Product Quality Planning (APQP): A Quality Framework for developing new products’, Published in proceeding of National conference on Quality Engg., D.Y.C.O.E., Akurdi. |
| 6 |
18th-19th
Jan. 2007 |
‘A review of machining performance evaluation of commercially available coatings on tungsten based cemented carbide tools’, Proc. Of National conference on Factory Automation, Robotics Computing, NIT, Warangal. |
| 7 |
11-12
April 2006 |
Presented paper “Prediction of change in friction in diesel engine by using Shaining DOE Techniques”, Published in proceeding of National conference on B. A. I. O. T., Coimbatoure, T.N. |
| 8 |
18-19 Nov.-2005 |
“An agent based computer approach for computer aided process planning”, proceeding of National conference on Sun Raising Technologies by PCOE, Thane, Mumbai. |
| 9 |
18-19 Nov.-2005 |
“An agent based system approach for enhancing manufacturing product development”, proceeding of 1st national conference on recent development in Mechanical Engineering SVERI’S COE, Panndharpur. |
| 10 |
18-19 Nov.-2005 |
“A genetic algorithm for conflict resolution in concurrent production development”, proceeding of a National conference on Sun raising technology, PCOE, Thane, Mumbai |
| 11 |
2-3 Dec.-2005 |
“Comparative analysis using analytical and finite element method of constant stress developed between two rolling discs”, Proc. Of National conference on Technological Advancements in Mech. Engg. SIST, Hydrabad. |
| 12 |
27-28 Feb.2006 |
“Fused deposition modeling method used for design and preparation of rapid prototyping model of semi enclosed impeller”, proceeding of National conference on advances in CAD/CAM, JNTU, Kakinada, A.P. |
| 13 |
23-24 July-2004 |
“Sixsigma an application of stastical methods to business process for improving operating efficiencies – A case study”, National conference on recent trends in Mechanical Engg. SRES COE, Kopargaon. |
| 14 |
9-10 July-2004 |
“Face milling tool path generating of work part using unigraphics-CAM”, national conference on global technologies in manufacturing and thermal sciences, SE TNU Institute of Technology. |
|
| |
| Prof.C.R.Ramtirthkar |
| Sr. No. |
Date |
Title of the Paper and Journal. |
| 1 |
10 Jan 2003 |
C.R.Ramtirthkar, N.V. Sahasrabudhe, “Investigation of time constant for Solar Cooker”, Journal of Institution of Engineers. |
|
| |
| Prof. A.P.Kulkarni |
| Sr. No. |
Date |
Title of the Paper and Journal. |
| 1 |
10 Jan 2006 |
P.R. Randive, A.P. Kulkarni, S B Thombre, “Effect of fin array parameters on variation in heat transfer coefficient for natural convection in fins “WSEAS Transaction , volume 1, pp 567 -572 |
| 2 |
10 January 2008 |
A.P.Kulkarni, P.P.Deshpande “ Computer Simulation studyon Delhi Iron Pillar : Estimation of Weight”, Current Science, Vol. 94, No. 1, pp 120-123 |
| 3 |
19-21 June, 2006 |
A.P.Kulkarni, D.G. Thakur, M.Sadaiah, S.Gaikwad P.R. Randive, “Computer Control, Gantry Type Oxy-Acetylene Profile Cutting System”, The 10th Mechatronics Forum Biennial International Conference, MX2006—MECHATRONICS 2006, Penn State Great Valley, Malvrn, USA, |
| 4 |
July 19 – 22, 2006 |
A. P. Kulkarni, D. G. Thakur, M. Sadaiah, S. Gaikwad , “Computer Control, Gantry Type Oxy-Acetylene Profile Cutting System”, 22nd International Conference on CAD/CAM, Robotics and Factories of the Future, CARs & FOF 2006, VIT Vellore, |
| 5 |
18th -20th Dec, 2006 |
Pitambar R. Randive, S B Thombre, A P Kulkarni (India) “Experimental Investigations on Variation in Heat Transfer Coefficient for Natural Convection in FIN” 3rd BSME ASME Intrenational conference on Thermal Engineering, Dhaka, Bangladesh, |
| 6 |
18-19 February, 2006 |
A.P.Kulkarni, D.G. Thakur, M.Sadaiah, S.Gaikwad “Microcintroller based, Gantry Type Oxy-Fuel Profile Cutting System”, National Conference On Emerging Trends in Nano Technology And Innovations In Design And Manufacturing, ETNMD-2006, NIT Rourkela, PP 52-64, |
|
| |
| Prof. P. D. Sonawane |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
29-30 Sept, 2000 |
“ Experimental Analysis of Impact loads on spur gear tooth under misalignment conditions”, Sixteenth National Convention of Mechanical Engineers & All India seminar on Future trends in Mechanical Engineering, Research & Development, Dept of Mech & Ind Engg, University of Roorkee, Roorkee. |
| 2 |
7-9 Dec, 2006 |
“Simulation and Analysis of Flow Inside a Scramjet Combustor”, 3rd International Conference on Fluid Mechanics and Fluid Power, Indian Institute of Technology, Mumbai |
| 3 |
9-11 Aug, 2007 |
“CFD Analysis of Hypersonic Flow around a Power Law Body” Engineering Design 2007 Conference, Indian Institute of Science, Bangalore. |
| 4 |
26-27 Oct, 2007 |
, “Slender Bodies at Hypersonic Speeds”, IDST-MSAT 2007, Missile Complex, DRDL, Hyderabad |
| 5 |
21-22 Nov, 2008 |
, “Slender Aerodynamic Bodies for High
Speed Armaments”, National Conference on Advances on Armament
Technology, ARDE, Pashan, DRDO, Pune,
|
|
| |
| Prof. A. R. Mache |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
10-12th
Jan-2007 |
“Theoretical and Experimental Dynamic Response Analysis of a Road Vehicle Suspension System Using an Electromagnetic Damper”, International Conference on Advances in Machine Design & Industry Automation-2007 (ICAMDIA- 2007), Government College of Engineering, Pune. PP 223- 229. |
|
| |
| Prof. Abhijeet Rajeshwarrao Deshpande |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
March / April 2010 |
Statistical Modeling of GTAW for Weld Strength and Hardness in Welding Zone w. r. t. 304, THE TECHNOLOGY WORLD, ISSN 2180-1614 |
|
| |
| Prof. ABHIJIT SOBALE |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
2005 |
CAE Used for Durability Analysis ~ A Case Study.
(Paper no: 2005 - 26 - 330) SAEINDIA International Mobility Engineering Congress and Expo 2005. |
| 2 |
2006 |
Finite Element Analysis of a hydraulic valve-mounting bracket for its durability. (Paper no: DA 77) International Conference on Global Manufacturing and Innovation (An Advanced Optimization Technology Approach) GMI 2006
|
|
| |
| Prof. Yashwant S. Munde |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
4 to 6th Jan 2010 |
“Design and analysis of fiber reinforced composite laminates for optimum weight based on strength criteria” in International conference on advances in mechanical Engineering at SVNIT, Surat, Gujarat, India |
|
| |
| Prof. (Dr) Dinesh N.Kamble |
| Sr. No. |
Date |
Title of the Paper |
| 1 |
Sept 30,2010 |
“Slab Method Modification And Its Experimental Investigation For Hot Forming Process” Journal Of Materials and Manufacturing processes, 25 1-7, 2010 |
| 2 |
Aug 16,2010 |
“Design Of Expert System With Knowledge Base As A Modified Slab Method For Forging Of Connecting Rod” International Journal of Applied Artificial Intelligence, 2010, 24:1-17 |
| 3 |
Dec 10-12, 2008 |
“Prediction of Process Parameters in Forging of Connecting rod by applying Slab Method to design automated rule based system.” 2nd International conference AIMTDR, 2008, Organized by IIT Chennai, pp-11-18. |
| 4 |
Dec 18-20, 2009 |
“A Computational Slab Method and Its Modification for analysis of forging process to design knowledge base system” International Conference on Simulation Modelling and Analysis, NIT Culicat, Dec.2009, pp-118 |
| 5 |
Jan 21-23, 2009 |
“Analytical investigation of process variables in forging of connecting rod by applying slab method to develop an expert system” International conference CMES-09, Hyderabad, 2009, pp-287-294 |
| 6 |
June 7-9, 2007 |
“Prediction of maximum permissible process variables in forging of connecting rod to develop an expert system.” 15th ISME International Conference on Advances in mechanical Engineering, Bhopal, 2007, pp-111-119 |
| 7 |
Dec 13-15,2010 |
“Theoretical and Experimental Investigation to Design Knowledge Based System for Forging Process.” International conference AIMTDR, 2010, Organized by Andhra University Vishakhapatnam, India. pp-729-734 |
|
| |
|
